RESUMEN
This paper presents data on the macroscopic polarization of copolymer films of vinylidene fluoride with tetrafluoroethylene obtained with a modified apparatus assembled according to the Sawyer-Tower Circuit. The kinetics of the polarization process were analyzed taking into consideration the contributions of both bound and quasi-free (impurity) charges. It was shown that an "abnormal" decrease in conductivity was observed in fields near the coercive fields. This could be associated with the appearance of deep traps of the impurity charge carriers formed by the polar planes of ß-phase crystals. The conductivity data obtained from the charge and current responses differed. It was concluded that chain segments contributing to polarization with sufficiently low fields were present in the amorphous phase. A comparison showed that the average size of ß-phase crystals (crystals of X-ray diffraction reflection width) was almost one order of magnitude lower than the domain size obtained using piezoresponse force microscopy (PFM). The analysis of the fast-stage dielectric response before and after polarization indicated that as the external polarizing field increased in the ferroelectric polymer chains, conformational transitions occurred according to the T3GT3G- â (-TT-)n и TGTG â (-TT-)n types. This was accompanied by an increase in the effective dipole moment in the amorphous phase chains. The analysis of the IR spectroscopy data obtained in transmission and ATR modes revealed a difference in the conformational states of the chains in the core and surface parts of the film.
RESUMEN
The values of the surface potentials of two sides of films of polyvinylidene fluoride, and its copolymers with tetrafluoroethylene and hexafluoropropylene, were measured by the Kelvin probe method. The microstructures of the chains in the surfaces on these sides were evaluated by ATR IR spectroscopy. It was found that the observed surface potentials differed in the studied films. Simultaneously, it was observed from the IR spectroscopy data that the microstructures of the chains on both sides of the films also differed. It is concluded that the formation of the surface potential in (self-polarized) ferroelectric polymers is controlled by the microstructure of the surface layer. The reasons for the formation of a different microstructure on both sides of the films are suggested on the basis of the general regularities of structure formation in flexible-chain crystallizing polymers.
RESUMEN
Alginate hydrogels with embedded rigid percolating network of halloysite clay nanotubes were evaluated as a novel ink for 3D printing. Hydrophilic alginate macromolecules adsorbing on halloysite stabilize the network of the nanotubes and form their own network of interlaced polymer chains. The effect of halloysite content on the structure and properties of the hydrogels was studied by rheometry, thermogravimetric analysis, FTIR-spectroscopy, dynamic light scattering, transmission electron microscopy, and 3D cryo-electron microscopy. Hydrogels demonstrate a very pronounced shear-thinning at extrusion and rather quick viscosity recovery after extrusion assigned to rapid rearrangement of the network structure promoted by mobile alginate chains. Even at low volume fractions (up to 0.054) the nanotubes reinforce the hydrogel increasing its storage modulus up to 650 Pa and inducing the appearance of yield stress. These properties make the alginate/halloysite hydrogels promising for the application in 3D printing for fabrication of green and sustainable nanocomposite materials made from natural components.
RESUMEN
Rapidly growing 3D printing of hydrogels requires network materials which combine enhanced mechanical properties and printability. One of the most promising approaches to strengthen the hydrogels consists of the incorporation of inorganic fillers. In this paper, the rheological properties important for 3D printability were studied for nanocomposite hydrogels based on a rigid network of percolating halloysite nanotubes embedded in a soft alginate network cross-linked by calcium ions. Particular attention was paid to the effect of polymer cross-linking on these properties. It was revealed that the system possessed a pronounced shear-thinning behavior accompanied by a viscosity drop of 4-5 orders of magnitude. The polymer cross-links enhanced the shear-thinning properties and accelerated the viscosity recovery at rest so that the system could regain 96% of viscosity in only 18 s. Increasing the cross-linking of the soft network also enhanced the storage modulus of the nanocomposite system by up to 2 kPa. Through SAXS data, it was shown that at cross-linking, the junction zones consisting of fragments of two laterally aligned polymer chains were formed, which should have provided additional strength to the hydrogel. At the same time, the cross-linking of the soft network only slightly affected the yield stress, which seemed to be mainly determined by the rigid percolation network of nanotubes and reached 327 Pa. These properties make the alginate/halloysite hydrogels very promising for 3D printing, in particular, for biomedical purposes taking into account the natural origin, low toxicity, and good biocompatibility of both components.
RESUMEN
The synthesis of 1,2-di-tert-butyl-3,3-dimethylcyclopropene (I) is performed and its IR and Raman spectra are measured. Optimized geometries of I are obtained at the HF/6-31G* and CCSD/cc-pVDZ levels. The ab initio calculated spectra are used for the assignments of the experimental spectral data. The results obtained are compared with the corresponding data for 3,3-dimethylbut-1-ene and 3,3-dimethylcyclopropene. These experimental data and the total vibrational analysis of I supplement the information obtained in the series of investigations of tert-butyl, trimethylsilyl, trimethylgermyl, trimethylstannyl, and trimethylplumbyl derivatives of 3,3-dimethylcyclopropene.
